Horizontal stripes appear intermittently on the monitor. What to do if stripes appear on the monitor

The appearance of a vertical stripe on the monitor is a common problem. It can be provoked by various reasons, which can be detected by carrying out some manipulations. It is worth considering the color of the strip, which can be black, white or colored.

Why do vertical stripes appear on the monitor screen?

To get a picture on the display, you need a graphics chip, which is placed separately on a video card or integrated into the central processor. Information from it is transmitted through a cable to the screen, and the motherboard controls the system. Based on this, we can identify the reasons why vertical stripes appear on the monitor:

Rarely, the problem is a malfunction of the motherboard, since this part is practically not susceptible to damage. The board fails more often due to an existing marriage, after short circuits, a power surge, and due to other problems. In addition, it is worth noting that when the motherboard breaks, only stripes rarely appear, since other failures are also observed.
If vertical stripes appear on the monitor, then often the reason lies in the video card, the breakdowns of which are associated with the degradation of the chip crystal due to overheating.
To transfer the image in laptops, a cable or cable is used that is connected to the motherboard and to the display. If this part is pinched or damaged, streaks will appear on the monitor.
The most common cause concerns matrix failures. It should be borne in mind that the screen on a laptop is very fragile and if you close the device carelessly, you can damage the matrix.
It is rare, but it is possible for stripes to appear on the monitor due to drivers, so the first thing to do when stripes occur is to reinstall the “firewood”.

Vertical pink stripe on monitor

In most cases, multi-colored stripes on the screen are associated with a breakdown of the monitor matrix. This can happen as a result of failures in the power supply system, falls, shocks and other similar impacts or wear of parts. If a vertical stripe appears on the monitor, which is colored pink or purple, then this most often indicates a malfunction of the scaler. The appearance of such a defect can also be observed on new monitors, and it's all about a factory defect.

Vertical white line on the monitor

White, like any other color of the stripes, often indicates problems in the operation of the matrix. If, with a slight pressure or other influences on this part, the interference disappears and reappears, then this indicates the need to replace the part, since it has already failed. When vertical stripes appear on the computer monitor screen that are barely visible and flickering, then this may be due to a malfunction of the VGA wire or power filter that powers the monitor.

Vertical blue stripes on the monitor

Many users after a long game, when the equipment overheats or the video card is worn out, notice that vertical blue stripes have appeared on the monitor screen. In this case, if the warranty remains, then the video card should be replaced. There is another reason that vertical blue or light blue stripes appeared - possible damage to one of the contacts of the matrix cable or detachment of video processor solder balls from the BGA substrate due to overheating.

Yellow vertical bar on monitor

To determine the cause of the failure, you need to carry out some manipulations. If a vertical stripe appears on the LCD monitor, then disconnect it from the system unit and connect it to the network. If the strip has disappeared - there are problems in the operation of the video card, so it is necessary to check the cooling system and install new drivers. If the stripes remain, then most likely the defect is related to the display. When a vertical stripe of yellow or another shade appears on the monitor, you should look for swollen capacitors on the video card and replace them.

Vertical red bar on monitor screen

There are users who complain that distortions periodically appear on the screen. If you are interested in why vertical red stripes appear on the monitor, then you should know that often it's all about poor contact of the matrix cable. Rarely, the problem can be triggered by the combustion of elements. Rectangular areas consisting of vertical stripes are a signal of dust or damage to the cable connection connectors. Other reasons: a track has detached on the control board, or the video controller cable or VGA wire is damaged.

black vertical line on monitor

According to reviews, black stripes are sometimes visible on the screen, which can be located on different sides and even in the center. A thin vertical stripe on the monitor occurs if there has been a malfunction or breakdown in the operation of the video card, matrix or its cable. If, nevertheless, it was determined that the whole thing was a malfunction in the matrix, then it would not be possible to fix the problem and the only solution is to replace the part.

Vertical stripes appear on the monitor - what should I do?

Actions when stripes are detected will be directly related to the cause that triggered the failure:

First, let's figure out how to remove the vertical bar on the monitor if the video card is faulty. First, check the quality of the cooling system, for example, run a special program that determines the temperature. Disassemble the computer and remove the accumulated dust and change the thermal paste. For laptops, use a stand with additional fans.
If the problem arose due to a faulty motherboard or cable, then it is better not to experiment and not try to fix the breakdown on your own, so as not to aggravate the situation, so take the monitor or computer to a service center for diagnostics.

Rostislav Kuzmin

Good day, dear readers and subscribers of my blog! A computer is a complex device where all the elements are subtly interconnected. Poor quality work of one of the nodes can lead to equipment defects. In order for the equipment to serve for a long time, it is necessary not only to take care of it, but also to carry out diagnostics. This will allow you to identify the malfunction in a timely manner. Not every user will be able to do this on their own. Today I will tell you what to do if horizontal stripes appear on the monitor screen, how to remove it will be described below. It is not uncommon for a problem to be caused by a technical breakdown, but it pleases the fact that there is usually nothing critical in this, which means that it is quite possible to cope on your own.

A monitor is a means of displaying an image on a display. It is closely related to various computer components. Sometimes multi-colored stripes are the result of a driver malfunctioning or a failure due to a virus. But software problems are rarely the root cause. More often, the reason is the incorrect connection of the PC nodes or the negative impact of one of them on the other.

Before starting the diagnosis, it is worth checking what kind of defects on the screen. If the picture is simply deformed or the colors are inverted, then the likely cause is in the driver. Its updating is a simple task. It is best to download the latest version from the manufacturer's website. In the case when the screen is divided into strips or breaks up into pixels, then the reason is clearly in the hardware, and not in the software. Not all users know what to do in this case. Many blame the graphics card, but that may not be the issue. Loose wires, overheating, dust are all possible sources of streaks. Therefore, first of all, I recommend disconnecting the computer from the network and starting a sequential diagnosis of each element.

Monitor

Why can a monitor fail? More often this is a physical impact - impact, increased moisture, sunlight on the matrix. Sometimes a power surge or interference in the network can ruin the device. For all users, I recommend connecting the monitor to the electrical network through a surge protector. This is a good way to protect. There is a nuance here. Sometimes an extension cord is used instead of a surge protector. When you connect different devices to it, noise may occur, which cause distortion of the image. In this case, we check the monitor by separately connecting it to the network. If this does not help, then refer it to a friend. This is the easiest way to rule out monitor failure and start checking the rest of the computer.

video card

The second node that is responsible for displaying the image on the screen is the video card. It processes the incoming data and forms a picture. Like any device, it can burn out or deteriorate. In addition, it is subject to heat, clogging and other unpleasant phenomena. Diagnostics of the video card consists in cleaning it of dust, checking the operation of the cooler, and lubricating it if necessary. It is also important to check the integrity of the connection wires. Often the reason lies in them. The system unit accidentally touched by the foot, the wires that came off the connector - that's the distortion of the image.

If this does not help, all the wires are intact, the card does not heat up and is not dirty, then repeat the previous paragraph. He removes the video card and again we go to visit a friend. The video card is working. So we are looking for a problem further.

plumes

Service employees often talk about the fact that most of the breakdowns are solved by checking or replacing the connection wires. It was said above that you need to check how the video card is connected. However, it does not hurt to consider the cables that connect other components. What is the verification? We eliminate dust, check the reliability and correct connections, inspect the wires for black dots, bends and fractures. Many users for many years of using technology do not look inside their system unit and do not suspect what kind of anarchy reigns there. A lot of wires, mixed up with each other, covered with dust, and sometimes cobwebs. All this will naturally affect the work. To make my work easier in the future, I recommend inspecting the system unit after purchase, switching the wires and trying to lay them as evenly as possible. In the future, this will avoid breakdowns.

When switching wires and checking the connection, it will not be superfluous to inspect the motherboard. There are many elements on it and an unprepared user is unlikely to find a problem himself. But it is quite possible to notice small defects. These are burnt resistors. These are small protruding parts. Most often they have the shape of a cylinder, they can be of various colors - black, green, red. The burnt transistor will be black and with traces of soot. The second sign of its failure is bloating. It’s not worth changing them yourself, but this is a call to the fact that it’s time to take the PC to a service center.

Checking the monitor matrix

Above, I mentioned that the appearance of stripes is often the result of a hardware failure. But sometimes the nuances lie in the setting. First, you should try resetting the monitor to factory settings. It is very easy to do this. On the body of the device there are buttons that allow you to change the gamma, brightness, contrast. Among them there is always a reset button to factory settings. It returns the monitor to factory settings.

To understand the correct operation of the monitor itself, it will not be superfluous to check for the integrity of the matrix and the presence of hidden factory defects. This trick is often used by sellers to sell services to customers. It all sounds tricky and complicated, but in fact it is done easily.

There are several ways:

use of a special program;
video launch;
Microsoft tools.

Option 1 - download special software to a USB flash drive and run it on a PC. There are a lot of programs, they take up little space, and they are quite easy to use.

Popular utilities include:

These utilities will allow not only to detect a broken pixel, but also to check the matrix for color transitions and contrast. In general, the test is to drive the device to fill with one color. The dead pixel will be highlighted in a different color. Special images with gradation will help you determine if the colors are displayed correctly.

Option 2 - go to youtube and enter the query "matrix test" in the search. The principle is similar, only you do not need to download anything. We just start the video, expand it to full screen, remove all unnecessary elements and carefully look.

Option 3 - in the OS settings there are special items that allow you to customize the desktop. Among other things, you can choose a background here. The verification process boils down to removing all elements from the desktop, the taskbar and sequentially filling it with one color. In other words, this is a variation of the first option, you just have to dig a little in the settings. I do not recommend using this method, because it is the longest. Suitable if there is no Internet and special utilities.

For those who decide to turn to this method, the sequence of actions is as follows:

Personalization - Options.
Background - Solid Color - Complementary Color.
You need to choose alternately white, gray, black, green, red, blue colors. It is on them that the pixels are noticeable.
We return to the Personalization menu and go to the Taskbar.
Select "Auto-hide the panel on the desktop". Now she will hide on her own outside the screen. To return it to its place, just move the cursor down.
Last point. We click on the table with RMB and go to the "View" item. At the bottom, check "show desktop icons".
After completing these steps, nothing will remain on the desktop except the selected color. The action must be repeated for each of the above colors.

It should be understood that the software and methods listed above are a way to find a matrix defect. Repair in this case comes down to replacing the matrix. This is an expensive pleasure and it can be carried out in a service center. I recommend doing a similar test for a new device. This should be done at the store, as if pixels at home or stripes are detected, the monitor will be difficult to change quickly. A quality check will be required, which takes 21 days. It is unpleasant to buy a new monitor and wait 3 weeks for it to be changed.

Setting

If the stripes on the screen are faintly visible, and they are more like an incorrect display of colors, then you can try to fix this by adjusting. There are a number of special programs that allow you to achieve the most accurate display of colors.

The appearance of stripes on the screen is not a reason to buy a new monitor, video card or system unit. You can often fix a defect yourself, and I hope this article will help you do that.

If you want to be in the know, I'm in instagram, where I post new articles that appear on the site. Also there is my personal blog.

Thank you for your attention! See you again on my blog! Sincerely, Rostislav Kuzmin.

cool

The appearance of stripes on the monitor screen is a fairly common phenomenon. Sometimes they indicate an incorrect image setting, more often a device malfunction.

The stripes on the monitor can have different colors, intensity, width and direction. The image in these areas of the screen may be doubled, blurry or completely absent. Black, white, or colored stripes may appear at the top, bottom, edges, or other parts of the monitor screen. As a rule, they occur immediately after turning on the PC, but they can also appear during operation. Often you can see flickering stripes on the monitor. Each of these cases is a consequence of significant problems in the operation of the device.

Why do lines appear on the monitor?

Based on the number of options for the location of the bands on the monitor screen, the reasons for their appearance can be completely different. Often the so-called image artifacts in the form of longitudinal and transverse stripes can be caused by malfunctions of the video card or motherboard. However, in some cases we are talking about a malfunction of the monitor itself.

wide black bars at the bottom and top of the monitor screen or along its edges, usually appear as a result of improperly setting the aspect ratio of the image.

If the monitor appears wide vertical or horizontal stripe gray or colored shade, we can talk about damage to the matrix or the cable connecting it to the control board. Stripes can also occur as a result of mechanical impact on the matrix, for example, during careless transportation or strong pressure on the screen.

Thin vertical stripes appear on the monitor screen due to detachment of the tracks of the matrix driver or its direct failure.

Also, the cause of the appearance of stripes may be a damaged video signal cable connecting the monitor to the video card, or poor contact on the connectors.

What should I do if stripes appear on the monitor?

You can remove stripes from the screen on your own only in some simple cases. For example, using the settings of the monitor itself or the video card driver. But in most more complex cases, it is better to seek the help of a specialist, especially if the matrix or control board components are faulty.

The appearance of stripes on the laptop screen belongs to the category of complex breakdowns. And if you hope that you will deal with this problem within a few minutes, then unfortunately you will not.

Difficulty in diagnosis

Diagnosing such a problem on a laptop is much more difficult than on a regular computer. This is due primarily to the design features of laptops and their more complex device.

Stripes on a laptop screen can be horizontal, vertical, black, white and colored, and the reasons for their appearance, as a rule, lie in the plane of problems with the hardware devices of the latter.

You can also see ripples on the screen, skewed images, specular color reproduction (black - gray, red - green, etc.), displaying the image as a negative.

Reasons for the appearance of stripes on the laptop screen

Let's look at the reasons for this phenomenon.:

1. The simplest reason in this situation is overheating of the video card.

For example, this situation was with the Dell M5110 laptop. In the lower part, in the area of a discrete video card (there are two of them), it heated up so much that the leatherette on which it stood began to melt and stick to it.

As a result, the periodic appearance of colored stripes on the screen and ripples. The problem was partially solved by purchasing a stand with laptop coolers. Stripes appear, but very rarely.

2. Complete failure of the video card.

As a rule, the main reason for such a breakdown is also overheating or hardware failure. The power supply handles power surges well, so this reason is unlikely.

In such a situation, either stripes appear on the screen even when the OS is loaded, or the laptop does not start at all.

This problem is solved by repairing or upgrading the video card. This is not easy to do on a laptop, you need to have the skills of at least a beginner electronics engineer. But we will talk about these points further.

3. The motherboard has failed.

The situation is repeatable with point 2, it is difficult to diagnose the problem, but it is possible. We will talk about this further.

4. The cable is out of order.

From the system board to the matrix there is a special loop through which the signal is transmitted.

Poor contact at the junction, burnout or fracture of the loop can cause interruptions in signal transmission to the matrix, hence the appearance of stripes.

5. Problems with the matrix, its failure.

The situation is critical, there is only one way out, the matrix needs to be replaced.

In this situation, it is rare that reinstalling or updating video card drivers helps, and hoping that this will help is not worth it, it is really a rare case.

Problem Diagnosis

The most important task in all this is to correctly diagnose the cause of the problem.

A complete diagnosis of the causes of the appearance of stripes on the laptop screen can only be carried out in service centers using special equipment.

But the initial diagnosis, which can also tell us a lot, is also possible at home.

With an optional monitor

An additional monitor can be connected to a laptop via a connector VGA.

There can be two results:

Everything will be displayed normally on an additional monitor;
Similar stripes will be displayed as on the laptop screen.

The result of paragraph 1 tells us that the laptop's video card is working, problems should be looked for in the matrix and laptop cable.

Result 2 tells us that there are problems with the motherboard and video card. In both cases, repairs are indispensable.

Checking the matrix

Checking the matrix at home is possible by the method of its partial deformation.
Try not to push the monitor screen hard in places with the most stripes.
Then gently, with both hands, try to slightly bend the screen in a horizontal plane.
Note in both cases how the colors of the stripes change, their contrast and brightness.
If the changes are visible, then the causes of the breakdown are in the matrix or loop.

When do you need to change the laptop matrix?

We replace the laptop matrix in cases:

Provided that a monitor is connected in parallel. If, when the matrix is deformed in the horizontal and vertical planes, its surface is pressed inwards, the color rendering of the stripes changes, the stripes disappear and reappear.
The presence of bands is observed at all stages of computer boot - BIOS, WINDOWS.
Ripples appeared on the screen, wide white or multi-colored stripes are visible.

The matrix gives the image in a negative or there is a substitution of colors, for example, it should be red, but green is displayed, blue is yellow, black is light gray, etc.

Checking the loop

The cable is flexible and this is understandable, because the laptop screen cannot be in the “stowed” position all the time, and this is not a computer. The deformation of the loop occurs constantly, respectively, the probability of its failure is high.
Slowly opening and quickly closing the lid and vice versa, unload according to how the stripes “behave”. Any changes on the monitor screen indicate that the cable is the source of the problem.

What does the matrix cable look like for the Asus X51RL laptop.

When do you need to "deal" with the loop?

Condition - a parallel connected monitor shows a clear picture.

It is necessary to repair, and it is better to change the matrix cable in cases where the image on the screen is fuzzy, ripples, periodically flickers, a large number of colored and white lines.
While the laptop is booting up and running, there are vertical columns of white pixels on the screen.
Opening and closing the lid "revives" all these errors on the screen.

video card

The video card requires attention if the screen of a laptop and a monitor connected in parallel give a picture with multi-colored lines, as well as other errors in the image are duplicated.

At the very beginning of the computer boot, there are no horizontal, vertical, black, white and colored bars, but at the Windows boot stage, the bars appear.
At the stage of loading Windows, the image disappears and a black screen appears.
Strong heating of the laptop in the area where the video card is located (the motherboard can also get warm).

Motherboard

The motherboard requires attention in the same cases as the video card (see above).
If the replacement of the cable, video card and matrix did not correct the situation.
Now let's look at ways to solve the problem with stripes on the laptop screen.

Ways to solve the problem

Plume

Problems with the cable going to the matrix most often occur in older laptop models. In new models, manufacturers are already using more advanced design solutions, thanks to which the cables last a very long time.

This is the complexity of the repair, it will be difficult, but possible, to find such a cable for an old laptop model.

Before you go to the radio market or electronics flea market, write down the model of the matrix, without it, no way.

In the service, they are unlikely to want to sell you such a rare “spare part”, and no one wants to lose a client, and suddenly you decide to give the laptop for repair to them.

If you find the right train, you are lucky, if not, then you can try to do everything yourself.

To do this, you will need minor electronics skills, a soldering iron, solder, rosin, a tester, and most importantly, an MGTF-type wire.

To ring the loop with a tester, you will have to get to both ends of it. The repair technology is simple, to the point of "disgrace".

We call, we find a break (if there is one), instead of a broken wire, we solder a backup wire parallel to it.

If there is no break, then the problem lies in more expensive components.

Motherboard

The motherboard may not fail completely. As a result of overheating of its individual section, the microchip or bus responsible for exchanging data with the video card may fail.

Also pay attention to the PCMCIA slot where the video card is inserted, if there are any burnt or oxidized contacts there. After all, they pour tea and coffee on laptops.

But in any case, without repair can not do. But first, order diagnostics, and if you are offered to re-solder any chip, you can still agree to clean the contacts.

A complex repair of a burnt motherboard does not justify itself, it is easier to replace it with a new one.

video card

With a video card, the situation is similar. A video chip is soldered on it, which, as a result of overheating, can fail.

There are three ways to go here. Consider them in descending order, in relation to the high cost and reliability of work.

Immediately replace this chip (expensive, but reliable);
Dismantle and reinstall the same chip - Rebowling (in most cases it gives a result);
Warming up the chip (pay less, but in 99% of cases the problem will recur after a while).

Which method to use, everyone decides for himself.

Burnt.

Do not forget, before leaving your laptop in the service, agree with the master on the prices for all types of work performed, and it is better to sag their contract.

Also, do not forget about the certificate of completion, which indicates the date of repair, what has changed or what has been repaired, as well as the warranty.

Outcome

Of course, it is impossible to describe all the situations when stripes appear on the laptop screen.

The problem is so specific and individual that in each case it requires a separate study.

It all depends on the laptop model, matrix type, design features and analysis, how often such problems appear on this particular model.

But if we take in percentage terms what was most often repaired and changed in this situation, then the cases with the replacement of the matrix - about 40%, the replacement or repair of the cable - about 20%, the video card - about 20%, the motherboard - approximately 20% (with taking into account the failure of the integrated video card).

As we can see, in most cases it is necessary to change the matrix, but this event is not cheap, if the cost of replacing it exceeds 50% of the price of a new laptop, then there is no point in such a repair, it’s easier to buy a new one.

But everyone decides for himself. We wish that the screens of your laptops always delight you with clear and bright images. Good luck.

Technical equipment, new technologies, a subtle but not necessary interconnection of various elements - this is what modern progress has come to. This, of course, is about a computer, which has a lot of elements that need care and careful monitoring so that they work correctly and do not break. But not every one of us can do this, so we are faced with various problems, which sometimes manifest themselves very strongly and cause a lot of inconvenience. Basically, we will talk about technical problems that are difficult to diagnose, but it is quite possible to fix it yourself. And in this article we will analyze where and why stripes appear on the monitor, which sometimes overshadow the entire picture on the screen. Fortunately, the problem is not always critical, so in most cases you can fix it on your own. And sometimes it is they who indicate that the equipment has broken down and urgently needs to be replaced.

What is this problem?

Before analyzing where the vertical stripes appeared on the monitor, it is worth considering the problem itself, which in most cases is of a technical nature. Yes, a program crash, a virus and other problems, even a driver-related option - all this is not the reason why defects appear on the monitor screen. This problem is a consequence of the negative influence of computer elements on the monitor or their incorrect interaction with each other. The problem is simple and critical, but it will become known only after a thorough diagnosis of the equipment. When this unpleasant situation occurs, various defective stripes begin to appear on the monitor, which bring with them a lot of trouble. Either completely obscure the entire monitor, or replace colors, or the screen completely breaks up into pixels.

Why does it arise?

If stripes appear on the monitor, this means that it is time to diagnose all the equipment. You should not blame everything on the video card in advance, as it is not always the main cause of the problem. Other elements of your equipment may be involved in this, which may affect this defect. It is worth completely excluding options that relate to programs, driver failures, since image distortion, which is also filled with extra stripes, is a guaranteed technical problem. Therefore, you can safely turn off the computer and start checking all your equipment for damage, dust, and much more.

The main causes of this problem

Vertical or horizontal streaks on the monitor may be due to equipment failure or overheating. It is also necessary to take into account the incorrect interaction of various technical elements. In addition, do not forget that the source of the problem may be dust and pollution of the plumes, which are the connecting connection between the various elements. Therefore, in order to establish the true causes, it is necessary to conduct a series of diagnostic studies that will identify the true problem, and only then think about ways that will help get rid of this unpleasant situation. And it is worth remembering that you should not immediately run to the service, since in most cases you can get out of this situation by your own efforts. Well, if a technical problem is classified as critical, then there are no options - you will have to find among your friends those who have experience in troubleshooting such problems.

video card

Horizontal stripes on the monitor and in general any defects on the monitor screen can be caused primarily by a malfunction of the video card. It is necessary to check if it works normally, if the cooler on it is dusty, which can cause the equipment to overheat, and if it is connected to the motherboard correctly, that is, if the wires are damaged. Yes, the graphics card is the imaging center that can cause the problem. Therefore, if you suddenly notice that the board itself is working normally, you should definitely clean it of dust with cotton swabs. Then check its connectors and try to clean them. After that, check the wires for physical damage. If not, then that's good news; if the wires are damaged, then the equipment will have to be replaced.

If no problems are found and everything is cleaned, it is worth conducting another check, which consists in examining the technical features of the video card. It sounds complicated, but in reality everything is simple: you need to check the hardware on another computer. A friend can help you with this: just insert a video card into his computer and see if there are stripes on his monitor. If there are no stripes, then the problem is different; if there is a defect, then the problem is in this graphics hardware. So, you should contact the service or buy a new video card.

Monitor malfunction

When vertical stripes appear on the monitor, do not panic. Just start checking your hardware. And it should be noted right away that the option with a monitor is also appropriate, although this element is not programmable. Any physical impact on the monitor can cause a lot of problems regarding image deformation. You can also note factors such as falling sunlight and exposure to high humidity on the monitor. To test this device, no special education is needed, just test it on another computer. Take advantage of this opportunity with a friend. If after connecting the stripes on the monitor disappeared, then the problem is in your computer; if there is an opposite result, then you need to contact a specialized service, since you can’t fix such a problem with your own hands.

Checking loops

Stripes on the monitor screen can also mean that you probably have problems in the connections of the elements themselves, which can sometimes be either physically damaged or simply dusty. To check them, you need to carefully examine every millimeter of the cable for physical damage. Are there black dots there? Is the loop positioned correctly? Does it have unnecessary curves? Is everything connected correctly? If there is such an opportunity, then it is worth checking them on another computer. In fact, the problem of loops is quite complicated, and not everyone can fully check these wires, therefore, in order to diagnose such a problem instantly, you must always have several spare loops on hand, which can be replaced if necessary. If, after using fresh wire options, stripes on the monitor continue to appear, then it is worth looking for the source of the problem in other equipment. And if there is no problem, then you have already solved it and you can continue to enjoy the possibilities of virtual space. It is worth remembering this nuance, since not many people know that this can also be the cause of an unpleasant situation.

Computer cleaning

Breakdown of internal elements

But do not forget about the possible breakdown of internal devices, which can also be the cause of defects on the screen. Basically, these elements include tracks and connecting elements on the motherboard. If you carefully check them, you can find that some strips have turned black, and the resistors are swollen. It is this state of affairs that is the cause of the breakdown, which cannot be fixed by one's own efforts. Therefore, if you find at least one of the items listed, then it is worth replacing the motherboard, since its repair will no longer be possible.

How to solve this problem?

Lines appear on the monitor. How to solve this problem? Actually, we have considered all possible solutions in this article, all of them are described above. First, it is necessary to diagnose the equipment, clean the computer, since dust can cause overheating of important elements of the computer, and then draw conclusions and look for a way out of this unpleasant situation. A vertical stripe on the monitor or another graphical defect - all this is caused by the problems that we examined with you. As for the ways to eliminate them, we also analyzed them, in particular, we mentioned the motherboard itself, which can serve as a source of negative impact. But it is, unfortunately, quite difficult to check it, so the only right decision can only be to contact a service center. Everything else can be checked and figured out what exactly is the cause of the defect on the screen.

Service is a guaranteed solution to the problem

A black bar on the monitor, splitting of the image into pixels of different sizes, disappearance of the image, incorrect colors - all this and much more indicates that there are problems with your computer. This article allows you to fix them or diagnose them yourself. But it happens that the hands are simply afraid to touch anything there and generally disassemble the computer. It is in such cases, when you are not confident in your abilities, that a specialized service center will help you, where they will provide all the necessary services. For a fee, they will clean your computer and restore the normal image on the monitor. And if the breakdown is critical, then they will definitely tell you what exactly the problem is and how to fix it. Now it has become much easier to navigate in this situation, which will undoubtedly serve as a positive new experience in terms of managing and controlling computer technology.