Sports transmission Opel Vectra a. Transmission input shaft seal

Show phone

Auto Plaza store offers a wide range of spare parts for used and new OPEL cars. Check with the manager for details and availability. Go to our Avito Store to see more spare parts (link on the right under the phone number and from the bottom under the description of the announcement) Delivery throughout Russia by the Transport Company. Our website address is in the "Contacts" section. We work every day without breaks and weekends from 10.00 to 19.00. Guarantee for goods 21 days

Opel Frontera Opel Cadet Opel Astra Opel Astra h g j gtc gts, Astra Ash n DJ, Corsa c d, Corsa c d, Meriva A B, Meriva A B, Zafira A B, Zafira A B, Vectra B C, Vectra B C, Omega B, Omega Antara,. Body sedan, station wagon, hatchback, restyling, dorestyling. robot, Easytronic, robotic gearbox, auto disassembly.
Capot.wing headlight lights optics front rear bumper, amplifier, bracket, with and without parking sensors, front rear left right driver's passenger passenger hinge door, trunk lid, roof, side member, panel, molding, handle, lining, lock, windshield side window, electric heated rear-view mirror, fender, trim, map, power window, buttons, light control unit, heater, climate control, stove, power windows, headlight, scythe wiring harness, connector, flashlight chip, PTF foglight external internal, main air conditioner radiator, cooling fan with diffuser, manual transmission , manual transmission, automatic, automatic, engine assembly, valve cover, cylinder head, cylinder block, piston, connecting rod, camshaft inlet outlet, crankshaft, oil pan, starter, generator, ignition coil module, fuel rail injector rail, ECU , throttle body, fuel tank pump, egr, manifold. CV joint, backstage, handbrake, console, dash torpedo, stove cabin fan, resistor, passenger airbag airbag, seat chair, radio, brain block, shelf, display, on-board computer, air filter housing, servo drive, mechatronics, twinport, twinport , tropezia, oil pump, pump, timing gears, phase regulator, pulley, crankshaft position sensor, camshaft, pressure, dmv, dpkv, mass air flow sensor, corrugation, lever, beam, subframe, fender liner, locker, casing, pump, wheel disk , fuse block, shock absorber strut assembly with spring, radiator grille, chrome, engine compartment wiring, braid, harness, support, bracket, compressor, jabot, wiper motor, trapeze, tidy, dashboard, doors sedan hatchback coupe caravan station wagon.

Show phone

Type 5 synchronized forward gears and 1 reverse gear Type Code Large ratio (WR) or small ratio (CR) – 14 NV F10 WR – 16 SV, C16 NZ, C16 NZ2 and X16 SZ F13 ...

13.2 General information

The gearbox is housed in an aluminum alloy crankcase and attached to the left side of the engine. It consists of a gearbox, final drive and differential. Torque from the crankshaft of the engine is transmitted through the clutch to the input shaft of the gearbox, on which the clutch disc is mounted. From the secondary shaft, the torque is transmitted to the differential ...

The prevention After carrying out adjustment close an aperture of a regulator in a cover of the mechanism of a choice of transfers a new stopper. The location of the clamping bolt that secures the gear selector rod to the rod Removing the plug from the adjustment hole in the gear selector cover ...

13.4 Shift Lever Assembly

Removal PERFORMANCE ORDER 1. In a motor compartment loosen a tightening bolt, fastening a rod of the mechanism of a choice of transfer to draft. 2. Remove the shift lever. 3. Remove the front of the center console. ...

Removal PERFORMANCE ORDER 1. Loosen the clamping bolt that secures the rod of the gear selection mechanism to the draft. 2. Remove the locking bracket, then remove the linkage universal joint shaft. 3. Remove the spring clip, then remove the main...

Removal Removal of a protective cover of the lever of a choice of transfers from the central console Removal of the lever of a gear change together with an articulated pin and bracket PERFORMANCE ORDER 1. For access to the base of the selector lever...

13.7 Protective cover for gear lever

Removal PERFORMANCE ORDER 1. Remove the gear change lever. 2. Heat the gear lever knob to +80° by immersing it in hot water for a few minutes, then unscrew and remove the knob from the gear lever. When removing the handle...

13.8 Differential O-rings

The prevention For performance of this operation it is necessary to use a stripper of spherical hinges. When installing, it is necessary to use a new locking ring of the drive shaft and a new cotter pin that fixes the nut of the ball joint connecting the lower arm to the front suspension strut. Removal PROCEDURE...

13.9 O-ring, transmission input shaft

The prevention At installation it is necessary to use a new sealing ring of the directing plug of the release bearing. Removal PERFORMANCE ORDER 1. Remove the release bearing and clutch release fork. 2. Unscrew the bolts and remove the bushing guide...

The prevention Removal and installation of a transmission - rather difficult operation therefore before its performance read the present section. When removing the gearbox, special equipment must be used to support the engine. When installing the gearbox, it is necessary to use a special tool to install the gearbox input shaft in...